Phosphine

Phosphine
Phosphine
Phosphine-3D-balls.png
Phosphine-underside-3D-vdW.png
Names
IUPAC name
Phosphane
Other names
Phosphamine
Phosphorus trihydride
Phosphorated hydrogen
Identifiers
3D model ( JSmol)
ChEBI
ChemSpider
ECHA InfoCard 100.029.328
EC Number
  • 232-260-8
287
PubChem CID
RTECS number
  • SY7525000
UNII
UN number 2199
Properties
PH3
Molar mass 33.99758 g/mol
Appearance Colorless gas
Odor Faint, fish-like or garlic-like[1]
Density 1.379 g/l, gas (25 °C)
Melting point −132.8 °C (−207.0 °F; 140.3 K)
Boiling point −87.7 °C (−125.9 °F; 185.5 K)
31.2 mg/100ml (17 °C)
Solubility Soluble in alcohol, ether, CS2
slightly soluble in benzene, chloroform, ethanol
Vapor pressure 41.3 atm (20 °C)[1]
Conjugate acid Phosphonium (chemical formula PH+
4
)
2.144
Viscosity 1.1×10−5 Pa⋅s
Structure
Trigonal pyramidal
0.58 D
Thermochemistry
37 J/mol⋅K
210 J/mol⋅K[2]
5 kJ/mol[2]
13 kJ/mol
Hazards
Safety data sheet ICSC 0694
GHS pictograms GHS02: Flammable GHS06: Toxic GHS05: Corrosive GHS09: Environmental hazard
NFPA 704 (fire diamond)
Flammability code 4: Will rapidly or completely vaporize at normal atmospheric pressure and temperature, or is readily dispersed in air and will burn readily. Flash point below 23 °C (73 °F). E.g. propaneHealth code 4: Very short exposure could cause death or major residual injury. E.g. VX gasReactivity code 2: Undergoes violent chemical change at elevated temperatures and pressures, reacts violently with water, or may form explosive mixtures with water. E.g. white phosphorusSpecial hazards (white): no code NFPA 704 four-colored diamond
4
4
2
Flash point Flammable gas
38 °C (100 °F; 311 K) (see text)
Explosive limits 1.79–98%[1]
Lethal dose or concentration (LD, LC):
LD 50 ( median dose)
3.03 mg/kg (rat, oral)
11 ppm (rat, 4 hr)[3]
LC Lo ( lowest published)
1000 ppm (mammal, 5 min)
270 ppm (mouse, 2 hr)
100 ppm (guinea pig, 4 hr)
50 ppm (cat, 2 hr)
2500 ppm (rabbit, 20 min)
1000 ppm (human, 5 min)[3]
NIOSH (US health exposure limits):
PEL (Permissible)
TWA 0.3 ppm (0.4 mg/m3)[1]
REL (Recommended)
TWA 0.3 ppm (0.4 mg/m3), ST 1 ppm (1 mg/m3)[1]
IDLH (Immediate danger)
50 ppm[1]
Related compounds
Other cations
Related compounds
Except where otherwise noted, data are given for materials in their standard state (at 25 °C [77 °F], 100 kPa).
☑Y verify (what is ☑Y☒N ?)
Infobox references

Phosphine (IUPAC name: phosphane) is a colorless, flammable, very toxic gas compound with the chemical formula PH3, classed as a pnictogen hydride. Pure phosphine is odorless, but technical grade samples have a highly unpleasant odor like rotting fish, due to the presence of substituted phosphine and diphosphane (P2H4). With traces of P2H4 present, PH3 is spontaneously flammable in air (pyrophoric), burning with a luminous flame.

Phosphine is also the general name given to the class of organophosphorus compounds of substituted phosphanes—a class of phosphanes in which the hydrogen atoms have been replaced with organic derivative, having a general formula PR3. Organophosphines are important in catalysts where they complex (adhere) to various metal ions; complexes derived from a chiral phosphine can catalyze reactions to give chiral, enantioenriched products.

History

Philippe Gengembre (1764–1838), a student of Lavoisier, first obtained phosphine in 1783 by heating white phosphorus in an aqueous solution of potash (potassium carbonate).[4][NB 1]

Perhaps because of its strong association with elemental phosphorus, phosphine was once regarded as a gaseous form of the element, but Lavoisier (1789) recognised it as a combination of phosphorus with hydrogen and described it as phosphure d'hydrogène (phosphide of hydrogen).[NB 2]

In 1844, Paul Thénard, son of the French chemist Louis Jacques Thénard, used a cold trap to separate diphosphine from phosphine that had been generated from calcium phosphide, thereby demonstrating that P2H4 is responsible for spontaneous flammability associated with PH3, and also for the characteristic orange/brown color that can form on surfaces, which is a polymerisation product.[5] He considered diphosphine's formula to be PH2, and thus an intermediate between elemental phosphorus, the higher polymers, and phosphine. Calcium phosphide (nominally Ca3P2) produces more P2H4 than other phosphides because of the preponderance of P-P bonds in the starting material.

The name "phosphine" was first used for an organophosphorus compounds in 1857, being analogous to organic amines (NR3).[NB 3][6] The gas PH3 was named "phosphine" by 1865 (or earlier).[7]

Structure and properties

PH3 is a trigonal pyramidal molecule with C3v molecular symmetry. The length of the P−H bond is 1.42 Å, the H−P−H bond angles are 93.5°. The dipole moment is 0.58 D, which increases with substitution of methyl groups in the series: CH3PH2, 1.10 D; (CH3)2PH, 1.23 D; (CH3)3P, 1.19 D. In contrast, the dipole moments of amines decrease with substitution, starting with ammonia, which has a dipole moment of 1.47 D. The low dipole moment and almost orthogonal bond angles lead to the conclusion that in PH3 the P−H bonds are almost entirely pσ(P) – sσ(H) and phosphorus 3s orbital contributes little to the bonding between phosphorus and hydrogen in this molecule. For this reason, the lone pair on phosphorus may be regarded as predominantly formed by the 3s orbital of phosphorus. The upfield chemical shift of the phosphorus atom in the 31P NMR spectrum accords with the conclusion that the lone pair electrons occupy the 3s orbital (Fluck, 1973). This electronic structure leads to a lack of nucleophilicity in general and lack of basicity in particular (pKaH = –14),[8] as well as an ability to form only weak hydrogen bonds.[9]

The aqueous solubility of PH3 is slight; 0.22 cm3 of gas dissolves in 1 cm3 of water. Phosphine dissolves more readily in non-polar solvents than in water because of the non-polar P−H bonds. It is technically amphoteric in water, but acid and base activity is poor. Proton exchange proceeds via a phosphonium (PH+
4
) ion in acidic solutions and via phosphanide (PH
2
) at high pH, with equilibrium constants Kb = 4×10−28 and Ka = 41.6×10−29.

Phosphine burns producing a dense white cloud of phosphoric acid:

PH 3 + 2 O 2 → H 3PO 4

Preparation and occurrence

Phosphine may be prepared in a variety of ways.[10] Industrially it can be made by the reaction of white phosphorus with sodium or potassium hydroxide, producing potassium or sodium hypophosphite as a by-product.

3 KOH + P 4 + 3 H 2O → 3 KH 2PO 2 + PH 3

Alternatively, the acid-catalyzed disproportionation of white phosphorus yields phosphoric acid and phosphine. Both routes have industrial significance; the acid route is the preferred method if further reaction of the phosphine to substituted phosphines is needed. The acid route requires purification and pressurizing. It can also be made (as described above) by the hydrolysis of a metal phosphide, such as aluminium phosphide or calcium phosphide. Pure samples of phosphine, free from P2H4, may be prepared using the action of potassium hydroxide on phosphonium iodide (PH4I).

Laboratory routes

It is prepared in the laboratory by disproportionation of phosphorous acid[11]

4 H 3PO 3 → PH 3 + 3 H 3PO 4

Phosphine evolution occurs at around 200 °C. Alternative methods involve the hydrolysis of aluminium phosphide, calcium phosphide, and tris(trimethylsilyl)phosphine.

Occurrence

Phosphine is a constituent of the Earth's atmosphere at very low and highly variable concentrations.[12] It may contribute significantly to the global phosphorus biochemical cycle. The most likely source is reduction of phosphate in decaying organic matter, possibly via partial reductions and disproportionations, since environmental systems do not have known reducing agents of sufficient strength to directly convert phosphate to phosphine.[13]

It is also found in Jupiter's turbulent atmosphere, where it forms in the planet's hot interior and reacts with other compounds in the upper atmosphere.[14] The abiotic synthesis of phosphine takes enormous amounts of energy, such as in the planet-sized convective storms of gas giants.[15]

Phosphine has also been detected in the temperate zone of Venus' atmosphere (approximately 50 km (31 mi) altitude) at 20 ppb, a concentration which is not possible with known chemical processes.[16] Venus lacks the high temperatures and pressures to form phosphine the way gas giants such as Jupiter do; thus another explanation for its presence is required.[17] It is not expected that phosphine would persist in the Venusian atmosphere, since being subject to ultraviolet radiation, it would eventually be consumed by water and carbon dioxide; thus it would have to be replenished. The paper announcing the discovery suggests that the phosphine "could originate from unknown photochemistry or geochemistry, or, by analogy with biological production of PH3 on Earth, from the presence of life".[16][17][18] For this reason phosphine has been proposed to be a usable biosignature for astrobiology. PH3 is associated with anaerobic ecosystems on Earth, which may be indicative of life on anoxic exoplanets. As of 2020, no known abiotic process generates phosphine gas on terrestrial planets in appreciable quantities, so detectable amounts of phosphine could indicate life.[19][20][21]

Phosphines

Organophosphines are compounds with the formula PRnH3−n. These compounds are often classified according to the value of n: primary phosphines (n = 1), secondary phosphines (n = 2), tertiary phosphines (n = 3). All adopt pyramidal structures. Their reactivity is also similar – they can be oxidized to the phosphorus(V) level, they can be protonated and alkylated at phosphorus to give phosphonium salts, and, for primary and secondary derivatives, they can be deprotonated by strong bases to give organophosphide derivatives.

Primary phosphines

Primary phosphines are typically prepared by alkylation of phosphine. Simple alkyl derivatives such as methylphosphine (CH3PH2) are prepared by alkylation of alkali metal derivatives MPH2 (M is Li, Na, or K). Another synthetic route involves treatment of the corresponding chlorophosphines with hydride reagents. For example, reduction of dichlorophenylphosphine with lithium aluminium hydride affords phenylphosphine (PhPH2).

Secondary phosphines

Secondary phosphines are prepared analogously to the primary phosphines. They are also obtained by alkali-metal reductive cleavage of triarylphosphines followed by hydrolysis of the resulting phosphide salt. The latter route is employed to prepare diphenylphosphine (Ph2PH). Diorganophosphinic acids, R2P(O)OH, can also be reduced with diisobutylaluminium hydride. Secondary phosphines are typically protic in character. But when modified with suitable substituents, as in certain (rare) diazaphospholenes (scheme 3), the polarity of the P-H bond can be inverted (see: umpolung) and the resulting phosphine hydride can reduce a carbonyl group as in the example of benzophenone in yet another way.[22]

Tertiary phosphines

Tertiary phosphines are generally obtained by treatment of phosphorus trichloride or triphenylphosphite with organolithium reagents or Grignard reagents. They are commonly used as ligands in coordination chemistry. Tertiary phosphines of the type PRR′R″ are "P-chiral" and optically stable.

Cyclic phosphines

Secondary and tertiary phosphines occur in cyclic forms. Three-membered rings are phosphiranes (unsaturated: phosphirenes), five-membered rings are phospholanes (unsaturated: phosphole), and six-membered rings are phosphinanes.

Applications

Organophosphorus chemistry

Phosphine is a precursor to many organophosphorus compounds. It reacts with formaldehyde in the presence of hydrogen chloride to give tetrakis(hydroxymethyl)phosphonium chloride, which is used in textiles. The hydrophosphination of alkenes is versatile route to a variety of phosphines. For example, in the presence of basic catalysts PH3 adds of Michael acceptors such as acrylonitrile:[23]

PH 3 + 3 CH 2=CHZ → P(CH 2CH 2Z) 3 (Z is NO 2, CN, or C(O)NH 2)

Acid catalysis is applicable to hydrophosphination with isobutylene and related analogues:

PH 3 + R 2C=CH 2 → R 2(CH 3)CPH 2 (R is Me, alkyl, etc.)

Microelectronics

Phosphine is used as a dopant in the semiconductor industry, and a precursor for the deposition of compound semiconductors. Commercially significant products include gallium phosphide and indium phosphide.[24]

Fumigant

For farm use, pellets of aluminium phosphide, calcium phosphide, or zinc phosphide release phosphine upon contact with atmospheric water or rodents' stomach acid. These pellets also contain agents to reduce the potential for ignition or explosion of the released phosphine. A more recent alternative is the use of phosphine gas itself which requires dilution with either CO2 or N2 or even air to bring it below the flammability point. Use of the gas avoids the issues related with the solid residues left by metal phosphide and results in faster, more efficient control of the target pests.

Because the previously popular fumigant methyl bromide has been phased out in some countries under the Montreal Protocol, phosphine is the only widely used, cost-effective, rapidly acting fumigant that does not leave residues on the stored product. Pests with high levels of resistance toward phosphine have become common in Asia, Australia and Brazil. High level resistance is also likely to occur in other regions, but has not been as closely monitored. Genetic variants that contribute to high level resistance to phosphine have been identified in the dihydrolipoamide dehydrogenase gene.[25] Identification of this gene now allows rapid molecular identification of resistant insects.

Safety

Phosphine gas is denser than air and hence may collect in low-lying areas. It can form explosive mixtures with air, and may also self-ignite.

Phosphine can be absorbed into the body by inhalation. Direct contact with phosphine liquid – although unlikely to occur – may cause frostbite, like other cryogenic liquids. The main target organ of phosphine gas is the respiratory tract.[26] According to the 2009 U.S. National Institute for Occupational Safety and Health (NIOSH) pocket guide, and U.S. Occupational Safety and Health Administration (OSHA) regulation, the 8 hour average respiratory exposure should not exceed 0.3 ppm. NIOSH recommends that the short term respiratory exposure to phosphine gas should not exceed 1 ppm. The Immediately Dangerous to Life or Health level is 50 ppm. Overexposure to phosphine gas causes nausea, vomiting, abdominal pain, diarrhea, thirst, chest tightness, dyspnea (breathing difficulty), muscle pain, chills, stupor or syncope, and pulmonary edema.[27][28] Phosphine has been reported to have the odor of decaying fish or garlic at concentrations below 0.3 ppm. The smell is normally restricted to laboratory areas or phosphine processing since the smell comes from the way the phosphine is extracted from the environment. However, it may occur elsewhere, such as in industrial waste landfills. Exposure to higher concentrations may cause olfactory fatigue.[29]

Toxicity

Deaths have resulted from accidental exposure to fumigation materials containing aluminum phosphide or phosphine.[30][31][32][33] It can be absorbed either by inhalation or transdermally.[30] As a respiratory poison, it affects the transport of oxygen or interferes with the utilization of oxygen by various cells in the body.[32] Exposure results in pulmonary edema (the lungs fill with fluid).[33] Phosphine gas is heavier than air so stays nearer the floor. [34]

Phosphine appears to be mainly a redox toxin, causing cell damage by inducing oxidative stress and mitochondrial dysfunction.[35] Resistance in insects is caused by a mutation in a mitochondrial metabolic gene.[25]

See also

Copyright