Voltage
Voltage  

Batteries are sources of voltage in many
electric circuits.


Common symbols

V , ∆V , U , ∆U 
SI unit  volt 
Derivations from
other quantities 
Voltage = Energy / charge 
Dimension  M L^{2} T^{−3} I^{−1} 
Voltage, electric potential difference, electric pressure or electric tension is the difference in electric potential between two points. The difference in electric potential between two points (i.e., voltage) in a static electric field is defined as the work needed per unit of charge to move a test charge between the two points. In the International System of Units, the derived unit for voltage is named volt.^{[1]} In SI units, work per unit charge is expressed as joules per coulomb, where 1 volt = 1 joule (of work) per 1 coulomb (of charge). The official SI definition for volt uses power and current, where 1 volt = 1 watt (of power) per 1 ampere (of current).^{[1]} This definition is equivalent to the more commonly used 'joules per coulomb'. Voltage or electric potential difference is denoted symbolically by ∆V, but more often simply as V, for instance in the context of Ohm's or Kirchhoff's circuit laws.
Electric potential differences between points can be caused by electric charge, by electric current through a magnetic field, by timevarying magnetic fields, or some combination of these three.^{[2]}^{[3]} A voltmeter can be used to measure the voltage (or potential difference) between two points in a system; often a common reference potential such as the ground of the system is used as one of the points. A voltage may represent either a source of energy (electromotive force) or lost, used, or stored energy (potential drop).
Definition
There are multiple useful ways to define voltage, including the standard definition mentioned at the start of this page. There are also other useful definitions of work per charge (see this section).
Roughly speaking, voltage is defined so that negatively charged objects are pulled towards higher voltages, while positively charged objects are pulled towards lower voltages. Therefore, the conventional current in a wire or resistor always flows from higher voltage to lower voltage.
Historically, voltage has been referred to using terms like "tension" and "pressure". Even today, the term "tension" is still used, for example within the phrase "high tension" (HT) which is commonly used in thermionic valve (vacuum tube) based electronics.
Definition as potential of electric field
The voltage increase from some point to some point is given by
In this case, the voltage increase from point A to point B is equal to the work which would have to be done per unit charge, against the electric field, to move the charge from A to B without causing any acceleration. Mathematically, this is expressed as the line integral of the electric field along that path. Under this definition, the voltage difference between two points is not uniquely defined when there are timevarying magnetic fields since the electric force is not a conservative force in such cases.
If this definition of voltage is used, any circuit where there are timevarying magnetic fields,^{[note 1]} such as circuits containing inductors, will not have a welldefined voltage between nodes in the circuit. However, if magnetic fields are suitably contained to each component, then the electric field is conservative in the region exterior^{[note 2]} to the components and voltages are welldefined in that region.^{[4]} In this case, the voltage across an inductor, viewed externally, turns out to be
despite the fact that, internally, the electric field in the coil is zero^{[4]} (assuming it is a perfect conductor).
Definition via decomposition of electric field
Using the above definition, the electric potential is not defined whenever magnetic fields change with time. In physics, it's sometimes useful to generalize the electric potential by only considering the conservative part of the electric field. This is done by the following decomposition used in electrodynamics:
where is the magnetic vector potential. The above decomposition is justified by Helmholtz's theorem.
In this case, the voltage increase from to is given by
where is the rotational electric field due to timevarying magnetic fields. In this case, the voltage between points is always uniquely defined.
Treatment in circuit theory
In circuit analysis and electrical engineering, the voltage across an inductor is not considered to be zero or undefined, as the standard definition would suggest. This is because electrical engineers use a lumped element model to represent and analyze circuits.
When using a lumped element model, it is assumed that there are no magnetic fields in the region surrounding the circuit and that the effects of these are contained in 'lumped elements', which are idealized and selfcontained circuit elements used to model physical components.^{[5]} If the assumption of negligible leaked fields is too inaccurate, their effects can be modelled by parasitic components.
In the case of a physical inductor though, the ideal lumped representation is often accurate. This is because the leaked fields of the inductor are generally negligible, especially if the inductor is a toroid. If leaked fields are negligible, we find that
is pathindependent, and there is a welldefined voltage across the inductor's terminals.^{[4]} This is the reason that measurements with a voltmeter across an inductor are often reasonably independent of the placement of the test leads.
Volt
The volt (symbol: V) is the derived unit for electric potential, electric potential difference, and electromotive force. The volt is named in honour of the Italian physicist Alessandro Volta (1745–1827), who invented the voltaic pile, possibly the first chemical battery.
Hydraulic analogy
A simple analogy for an electric circuit is water flowing in a closed circuit of pipework, driven by a mechanical pump. This can be called a "water circuit". Potential difference between two points corresponds to the pressure difference between two points. If the pump creates a pressure difference between two points, then water flowing from one point to the other will be able to do work, such as driving a turbine. Similarly, work can be done by an electric current driven by the potential difference provided by a battery. For example, the voltage provided by a sufficientlycharged automobile battery can "push" a large current through the windings of an automobile's starter motor. If the pump isn't working, it produces no pressure difference, and the turbine will not rotate. Likewise, if the automobile's battery is very weak or "dead" (or "flat"), then it will not turn the starter motor.
The hydraulic analogy is a useful way of understanding many electrical concepts. In such a system, the work done to move water is equal to the pressure multiplied by the volume of water moved. Similarly, in an electrical circuit, the work done to move electrons or other chargecarriers is equal to "electrical pressure" multiplied by the quantity of electrical charges moved. In relation to "flow", the larger the "pressure difference" between two points (potential difference or water pressure difference), the greater the flow between them (electric current or water flow). (See "electric power".)
Applications
Specifying a voltage measurement requires explicit or implicit specification of the points across which the voltage is measured. When using a voltmeter to measure potential difference, one electrical lead of the voltmeter must be connected to the first point, one to the second point.
A common use of the term "voltage" is in describing the voltage dropped across an electrical device (such as a resistor). The voltage drop across the device can be understood as the difference between measurements at each terminal of the device with respect to a common reference point (or ground). The voltage drop is the difference between the two readings. Two points in an electric circuit that are connected by an ideal conductor without resistance and not within a changing magnetic field have a voltage of zero. Any two points with the same potential may be connected by a conductor and no current will flow between them.
Addition of voltages
The voltage between A and C is the sum of the voltage between A and B and the voltage between B and C. The various voltages in a circuit can be computed using Kirchhoff's circuit laws.
When talking about alternating current (AC) there is a difference between instantaneous voltage and average voltage. Instantaneous voltages can be added for direct current (DC) and AC, but average voltages can be meaningfully added only when they apply to signals that all have the same frequency and phase.
Measuring instruments
Instruments for measuring voltages include the voltmeter, the potentiometer, and the oscilloscope. Analog voltmeters, such as movingcoil instruments, work by measuring the current through a fixed resistor, which, according to Ohm's Law, is proportional to the voltage across the resistor. The potentiometer works by balancing the unknown voltage against a known voltage in a bridge circuit. The cathoderay oscilloscope works by amplifying the voltage and using it to deflect an electron beam from a straight path, so that the deflection of the beam is proportional to the voltage.
Typical voltages
A common voltage for flashlight batteries is 1.5 volts (DC). A common voltage for automobile batteries is 12 volts (DC).
Common voltages supplied by power companies to consumers are 110 to 120 volts (AC) and 220 to 240 volts (AC). The voltage in electric power transmission lines used to distribute electricity from power stations can be several hundred times greater than consumer voltages, typically 110 to 1200 kV (AC).
The voltage used in overhead lines to power railway locomotives is between 12 kV and 50 kV (AC) or between 1.5 kV and 3 kV (DC).
Galvani potential vs. electrochemical potential
Inside a conductive material, the energy of an electron is affected not only by the average electric potential, but also by the specific thermal and atomic environment that it is in. When a voltmeter is connected between two different types of metal, it measures not the electrostatic potential difference, but instead something else that is affected by thermodynamics.^{[6]} The quantity measured by a voltmeter is the negative of the difference of the electrochemical potential of electrons (Fermi level) divided by the electron charge and commonly referred to as the voltage difference, while the pure unadjusted electrostatic potential (not measurable with a voltmeter) is sometimes called Galvani potential. The terms "voltage" and "electric potential" are ambiguous in that, in practice, they can refer to either of these in different contexts.
History
The term electromotive force was first used by Volta in a letter to Giovanni Aldini in 1798, and first appeared in a published paper in 1801 in Annales de chimie et de physique.^{[7]}^{:408} Volta meant by this a force that was not an electrostatic force, specifically, an electrochemical force.^{[7]}^{:405} The term was taken up by Michael Faraday in connection with electromagnetic induction in the 1820s. However, a clear definition of voltage and method of measuring it had not been developed at this time.^{[8]}^{:554} Volta distinguished emf from tension (potential difference): the observed potential difference at the terminals of an electrochemical cell when it was open circuit must exactly balance the emf of the cell so that no current flowed.^{[7]}^{:405}
See also
 Alternating current (AC)
 Direct current (DC)
 Electric potential
 Electric shock
 Electrical measurements
 Electrochemical potential
 Fermi level
 High voltage
 Mains electricity (an article about domestic power supply voltages)
 Mains electricity by country (list of countries with mains voltage and frequency)
 Ohm's law
 Ohm
 Opencircuit voltage
 Phantom voltage
References
Footnotes
External links
Other Languages
 Afrikaans
 العربية
 Azərbaycanca
 تۆرکجه
 বাংলা
 Bânlâmgú
 Беларуская
 Беларуская (тарашкевіца)
 Български
 Boarisch
 Bosanski
 Català
 Čeština
 Cymraeg
 Dansk
 Deutsch
 Eesti
 Ελληνικά
 Español
 Esperanto
 Estremeñu
 Euskara
 فارسی
 Français
 Gaeilge
 Galego
 한국어
 Հայերեն
 हिन्दी
 Hrvatski
 Bahasa Indonesia
 Interlingua
 Íslenska
 Italiano
 עברית
 Қазақша
 Кыргызча
 Latina
 Latviešu
 Lietuvių
 Magyar
 Македонски
 മലയാളം
 मराठी
 Bahasa Melayu
 Монгол
 မြန်မာဘာသာ
 Nederlands
 日本語
 Nordfriisk
 Norsk
 Norsk nynorsk
 ਪੰਜਾਬੀ
 پنجابی
 Polski
 Português
 Română
 Runa Simi
 Русский
 Scots
 Shqip
 Simple English
 Slovenčina
 Slovenščina
 Српски / srpski
 Srpskohrvatski / српскохрватски
 Basa Sunda
 Suomi
 Svenska
 Tagalog
 தமிழ்
 Татарча/tatarça
 తెలుగు
 ไทย
 Türkçe
 Українська
 اردو
 Tiếng Việt
 文言
 Wolof
 吴语
 ייִדיש
 粵語
 中文
Copyright
 This page is based on the Wikipedia article Voltage; it is used under the Creative Commons AttributionShareAlike 3.0 Unported License (CCBYSA). You may redistribute it, verbatim or modified, providing that you comply with the terms of the CCBYSA.